C-Band Transceiver Redundancy Switching Equipment 5700 series (C series, CE) (2 MB)
C-Band Transceiver Redundancy Switching Equipment 5900 series (C series, CE) (2 MB)
A range of 1:1 hub-mounting redundancy systems is available for CODAN 5700 series VSAT C-Band and CODAN 5900 series VSAT Ku-Band transceivers and high power SSPA.
CODAN VSAT satellite transceivers have been setting industry standards for performance and reliability since the early 1990's. However, there are still critical applications where 1:1 redundancy protection is required.
CODAN VSAT transceiver redundancy
CODAN offers a range of VSAT switching equipment that integrates easily with the CODAN 5700 series VSAT C-Band or CODAN 5900 series VSAT Ku-Band transceivers. The systems include interconnecting cables, mounting hardware and waveguide connections.
Simple configuration
A complete system comprises two standard transceivers, of any power rating, and the outdoor mounting VSAT Redundancy Controller CODAN 5586 that provides integral IF relays and simultaneously controls the RF switches. This configuration, also called stream redundancy, ensures unambiguous, simultaneous switchover of both IF and RF paths in the transmit and receive directions. The VSAT Controller is powered from both CODAN transceiver power supplies for high reliability.
Flexible configuration
Flexible operating modes allow 'warm' or 'hot' standby operation. Automatic or manual control is easily selected.
Generously rated terminations allow the off-line SSPA to be continuously activated for true hot standby capability. Test ports permit independent RF testing of the off-line stream, without interruption to the on-line traffic.
Owing to the unique design of control cables and connectors, the system can be reconfigured as a non-redundant system to restore operation should the controller require service.
Monitor and control
The optional one rack unit high Redundant System Monitor CODAN 5587 provides clear system status indication at all times, and remote manual control over VSAT SSPA activation and stream selection.
The individual transceivers' serial control ports are accessible at the rear of the CODAN 5587, enabling connection of ASCII (RS232) or Packet mode (RS485) control systems. Alternatively, a dual Remote Controller CODAN 5570D may be connected giving full control of both transceivers from the indoor equipment.
Stand-alone SSPA redundancy
An increasing number of customers are choosing CODAN high power outdoor antenna mounted SSPAs, fed from rack-mounted up converter systems, for their hub station installations.
CODAN offers compact 60W (CODAN 5760) and 120 W (CODAN 5712H) VSAT C-Band and 40W (CODAN 5940) VSAT Ku-Band SSPAs designed for operation in harsh outdoor environments. A 1:1 switching system is available to provide redundancy protection for these SSPAs.
SSPAs with 1:1 protection
CODAN high power VSAT SSPAs are easily integrated into a 1:1 system. The small SSPA Redundancy Interface Unit CODAN 5588 is mounted between the SSPAs and connects to a combination waveguide/coaxial switch to enable simultaneous switching of RF input and output paths. Waveguide bends, connecting cables and mounting hardware are provided.
Indoor monitor and control
Indoor status monitoring and manual/automatic control of the outdoor 1:1 VSAT SSPA system is achieved via the one rack unit high SSPA Redundancy Monitor CODAN 5589. The SSPAs can also be activated or muted from this panel.
Major configuration options
CODAN 5586 based VSAT redundancy system for VSAT C-Band transceivers
- Combined WR229/N-connector waveguide switch for VSAT SSPAs with N-type outputs
- Separate WR137 and WR229 waveguide switches for SSPAs with waveguide outputs
CODAN 5586 based redundancy system for VSAT Ku-Band transceivers
- Dual WR75 waveguide switches for Ku-Band SSPAs with waveguide outputs
CODAN 5588 based redundancy system for high power VSAT C-Band SSPAs*
- Combined WR137/N-connector waveguide switch for VSAT C-Band SSPAs with waveguide outputs
CODAN 5588 based redundancy system for high power VSAT Ku-Band SSPAs*
- Combined WR75/SMA-connector waveguide switch for VSAT Ku-Band SSPAs with waveguide outputs
Accessories
- Redundant System Monitor CODAN 5587 (for CODAN 5586 based systems)
- Dual Remote Controller CODAN 5570D (for CODAN 5586 based systems)
- SSPA Redundancy Monitor CODAN 5589 (for CODAN 5588 based systems)*
- Interconnecting cables for CODAN 5587 and CODAN 5589 units
- CODAN 5588/5589 system is not CE approved
CODAN quality and service
The redundancy equipment is built and tested in CODAN ISO9001 quality certified manufacturing facility.
CODAN fully trained staff and agents provide in-factory and in-country training services, and complete installation and on-site assistance. This service is backed up by a 24 hour customer service line and a warranty of three years on manufacturing, design or component defects.
CODAN VSAT Redundancy Switching System Specifications
IF/RF switching
Transmit and receive IF switching
|
Frequency range
|
50 to 180MHz
|
|
Impedance
|
50 Ω
75 Ω optional
|
|
Loss
- To on-line output
- To off-line output
|
0.5 dB maximum
50 dB minimum
|
|
Ripple
|
±0.05 dB typical over 70 ± 20 MHz and 140 ± 40 MHz
|
|
Transmit/receive isolation
|
90 dB minimum
|
| Connectors |
N-type female
|
| Return loss (on-line ports) |
20 dB minimum
|
|
Transmit IF splitter option
- Loss (to On output)
- Ripple
|
3.75 dB maximum
±0.07 dB typical over 70 ± 20 MHz and 140 ± 40 MHz
|
C-Band RF switching
|
Frequency range
- Transmit
- Receive
|
5.850 to 7.025 GHz
3.400 to 4.800 GHz
|
|
Switch loss
Transmit - coaxial N-type switch
Transmit - waveguide switch
Receive
|
0.5 dB maximum
0.1 dB maximum
0.1 dB maximum
|
|
Impedance (N-type switch)
|
50 Ω
|
|
VSWR
Transmit - Coaxial N-type switch
Transmit - Waveguide switch
Receive
|
1.3:1 maximum
1.1:1 maximum
1.1:1 maximum
|
|
Connectors
Transmit - Coaxial N-type switch
Transmit - Waveguide switch
Receive
|
N female
CPR137G flange, M5 threads
CPR229G flange, M6 threads |
VSAT Ku-Band RF switching
Transmit and receive paths use waveguide switches with identical specifications.
|
Transmit
|
13.75 to 14.5 GHz
|
|
Receive
|
10.95 to 12.75 GHz
|
|
Switch loss
|
0.05 dB maximum
|
|
VSWR
|
1.1:1 maximum
|
|
Connectors
|
WR75, PBR120 flange, M4 threads
|
Switching and control
Switching
|
Operating modes
|
Auto/manual
|
|
Switch-over time
|
1 s maximum
|
Monitor and control
|
Indicators
|
BUC1, BUC2 status
LNB1, LNB2 status
Redundancy controller status
Switch status and position
Fuse status
|
| Remote control |
Auto/Manual select
Stream select
|
CODAN Power supply
|
Input voltage
|
115/230 V AC +15%
|
|
DC to BUCs
Voltage
Power
|
48 V nominal
135W maximum to each BUC
|
DC to LNBs
Voltage
Power |
15 V nominal
9W maximum to each LNB |
Environmental
|
Operating temperature range
|
-40°C to +55°C
|
|
Relative humidity
|
100%
|
|
Weatherproofing
|
Sealed to IP66
|
Mechanical
|
Size
|
300mm W x 185mm D x 370mm H
|
Weight
|
CODAN 6586
|
14 kg
|
|
CODAN WR229/N switch
|
2.6 kg
|
|
CODAN WR229 switch
|
2.4 kg
|
|
CODAN WR137 switch
|
0.8 kg
|
|
CODAN WR75 switch
|
0.5 kg
|
